Zur Druckansicht wechseln Visit the English version of this page

www.jb-electronics.de » Elektronik » Nixie-Röhren » Nixie-Sammlung » GR-772

GR-772

Die GR-772 vom japanischen Hersteller Rodan ist eine seltene Anzeigeröhre mit einer Ziffernhöhe von 12mm:

Die GR-772 im Größenvergleich

Hier ist die GR-772 im Ruhezustand zu sehen:

Die GR-772 im RuhezustandDie GR-772 im Ruhezustand

Die GR-772 im RuhezustandDie GR-772 im Ruhezustand

Die GR-772 im Ruhezustand

Auffallend ist ihr seitlicher Vakuumstutzen, der sonst bei frontalen Nixies unten zwischen den Pins zu finden ist; doch die GR-772 besitzt einen speziellen Sockel, der dies verhindert:

Die GR-772 im RuhezustandDie GR-772 im Ruhezustand

Dieser Sockel ist auch notwendig, da die GR-772 zehn Symbole anzeigen kann, und somit inklusive Anodenanschluss mindestens elf Pins benötigt; der äußere Kreis des Sockels bietet aber nur zehn Pins, daher die mittleren zusätzlichen Anschlüsse. Hier ist das Leuchtbild der GR-772 zu sehen:

Das Symbol 'A'Die Ziffer 1

Die Ziffer 2Die Ziffer 3

Die Ziffer 4Die Ziffer 5

Die Ziffer 6Die Ziffer 7

Die Ziffer 8Die Ziffer 9

Das Symbol A fällt etwas aus dem Rahmen, was nahelegt, dass die GR-772 eine Spezialanfertigung sein könnte. Hier ist das Leuchtbild von der Seite aus zu sehen:

Das Leuchtbild der GR-772 von der Seite

Leider besitze ich kein Datenblatt zur GR-772. Sollte jemand im Besitz dieses Datenblattes sein, würde ich mich über eine Mail diesbezüglich sehr freuen.

Nach oben

show print layout Die deutsche Version der Seite besuchen

www.jb-electronics.de » Electronics » Nixie Tubes » Nixie Tube Collection » GR-772

GR-772

The GR-772 from the Japanese manufacturer Rodan is a rare Nixie tube with a digit height of 12mm:

The GR-772 in size comparison

Here you can see the GR-772 in state of rest:

The GR-772 in state of restThe GR-772 in state of rest

The GR-772 in state of restThe GR-772 in state of rest

The GR-772 in state of rest

The lateral vacuum seal is quite striking since for most front view Nixie tubes it is located between the pins at the bottom. For the GR-772 this is not possible, however, due to the special socket:

The GR-772 in state of restThe GR-772 in state of rest

This socket is necessary because the GR-772 can display ten symbols thus requiring eleven pins including the anode terminal: the outer circle of the socket only provides ten pins, making the inner pins necessary. Here you can see the glowing GR-772:

The symbol 'A'The digit 1

The digit 2The digit 3

The digit 4The digit 5

The digit 6The digit 7

The digit 8The digit 9

The symbol A does not really fit into the picture implying that the GR-772 is a specially made tube. Here you can see the glowing tube from the side:

The glowing display of the GR-772 from the side

Unfortunately, I do not have any datasheet for the GR-772. If someone can provide me with a datasheet, please email me.

To the top